![]() ![]()
!DA0xGI5K!WGoRMEFga1cHj3dCf7TORPoBIfcxXPaNFsF1STdM20oįgtech V54 0386 AES Software FIX for Win7-64bit – tested 100%ġ.Fix driver for win7-64bit. If you want to check CRP level of your NXP mcu you can do that with FlashMagic and USB-TTL adapter. ![]() You need also a jumper in position to do that. Reading and writing the mcu for this tool can be done with old Philips LPC 2000 software and USB-TTL adapter, preferd the one that uses PL2303 chipset. #Fgtech v54 license download how toHow to fix fgtech software not compatible with windows system:ġ.For tool number 0386: ept file,fix file,hex dump and 2 versions of programs V54 used for it, the one from china and the AES November software.Ģ.For tool number 0475: ept file,fix file, hex dumps made from my tool and program V54 for it that does not need time back.ģ.For both tools you have here how to connect to it, how to read firmware movie, how to write dump that you wish. !cJABgQbD!SlEUD1vM91ovCGuCrHzAT6891t7OKgdkydhDFnB1iCs In a word, being a professional ECU tunner, you need all above-mentioned tools.Topic: free offer source of FGTECH GALLETTO V54 0475 / 0386 FIX EPT HEX DUMP & PROGRAM source of FGTECH v error crash solution source of Fgtech V54 0386 AES Software FIX for Win7-64bit. Fgtech Galletto is the no tokens limitation while KESS V2 and Ktag will use tokens. Many ECU has the advantage that can be read and write from OBD port (so KESS V2 is perfect), but there are lot ECU that need to disassemble from the car and open and this is the case for all the ECU that need to be programmed with Jtag, BDM and Boot protocols, so KTAG is needed.įgtech Galletto ECU programming tool is perfect for both OBD use and BDM use. With KESS V2 you programming directly through the OBD port of the vehicle, while with Ktag you need to take apart the ECU and open it, after you can make the read/write operation. KESS V2 is a ECU programming tool that is perfect for OBD use, while KTag is perfect for Jtag, BDM and all the Boot application (tricore and ST10). Kess (even china good clone)…more stable than Mpps on can-line and good job on recovery…mpps good job on k-line (sometimes and can-line)…fgtech (i hate this tool)-but sometimes save your as…and best ktag-trasdata-no obd but safe boot mode,pinout direct conection and bdm…i talk about low price tools. It is expensive for the slave user who depend of a master.ĭifference among MPPS, Kess, Fgtech and ktag-trasdata : ![]() If you are a slave customer (who depend of a master (who do modificated), you read the programme (scripted by genius), you send it to the master, he do what you want (money paid) and he re-sent to you to write in the ecu machine. If you have master version you can work directly on the program you have write on the vehicle (tunning, egr off, ….) and rewrite after directly. Kess V2 v4.036 Ksuite V2.08-v2.28 Software Installation Video Ksuite software V2.3.2 is no video now, but Ksuite V2.08-v2.28 installation video for reference. Kess V2 V4.036 master (Item No.SE87-D), $159, best quality with higher price: (Best quality) se87-c, firmware V4.036, $69 (it was over $100), it is proved worth the money: ![]() #Fgtech v54 license download installConnect network – Not allowed, please disconnect the network before you install the software or use the device.Motorcycle – Fail, better use Fgtech V54(for the difference between FGTECH and KESS, skip to the last paragraph.).!tJJDgLBA!YUWWS9rYKf7usCjudk2dgve_xrxS9ePes0xIt-XjgZ4 (Crack and No password) Ksuite V2.3.2 is tested working 100% OK on kess V2 master FW4.036 FW4.024 ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |